Skip to content

Tennessee CDL study: Safe driving, vehicle control and cargo

Tennessee's 113 General Knowledge questions are split into a 70-question safe driving and cargo deck and a 43-question rules and licensing deck. Each shows 10 free questions with the reason behind the answer. Finish a deck, then test what you kept on General Knowledge run 1.

1/10·0 done

Question Map

Correct Wrong Unseen

10 of 70 questions are free. The rest are in Pro.

What is the typical brake lag time for air brakes compared to hydraulic brakes?

Free Safe driving, vehicle control and cargo questions for the Tennessee CDL test

Plain-text version of this question set

  1. What is the typical brake lag time for air brakes compared to hydraulic brakes?

    • A. There is no lag difference
    • B. Air brakes take about an additional second to engage compared to hydraulic brakes
    • C. Air brakes take 3-4 additional seconds
    • D. Air brakes have about a half-second delay

    Hint: Air must physically travel through lines before it can actuate the brake mechanisms.

    Explanation: Air brakes have approximately a half-second delay (brake lag) because air takes time to travel through the lines to the brakes, compared to the nearly instant response of hydraulic brakes.

  2. What is the typical cut-out and cut-in pressure range for the air compressor governor on a commercial vehicle?

    • A. 80-100 psi
    • B. 90-110 psi
    • C. 100-125 psi (cut-in) and 120-145 psi (cut-out)
    • D. About 100 psi cut-in and 125 psi cut-out

    Hint: The governor manages air pressure within a specific operating range by cycling the compressor on and off.

    Explanation: The air compressor governor typically cuts in (starts pumping) around 100 psi and cuts out (stops pumping) around 125 psi. These ranges ensure adequate air pressure for safe braking.

  3. The longer the combination vehicle, the more the trailer will off-track. What should a driver do when making a right turn with a long trailer?

    • A. Speed up through the turn to reduce off-tracking
    • B. Turn the steering wheel quickly to complete the turn faster
    • C. Turn from the far right lane to minimize the turning arc
    • D. Swing wide to the left before turning right

    Hint: Longer vehicles have more severe off-tracking, requiring a specific turning technique.

    Explanation: With longer combination vehicles, drivers should swing wide or use a jug handle turn, moving slightly to the left before turning right to give the trailer wheels room to clear the curb and any objects on the inside of the turn.

  4. When inspecting tires during a pre-trip inspection, which condition would require the tire to be replaced before driving?

    • A. A minor scuff mark on the sidewall
    • B. Tread depth of less than 2/32 of an inch on a steer tire
    • C. A tread depth of 5/32 of an inch on a drive tire
    • D. Slightly uneven tread wear across the tire

    Hint: Steer tires have stricter tread depth requirements than drive or trailer tires because they control the vehicle's direction.

    Explanation: Front (steer) tires must have at least 4/32 of an inch tread depth and all other tires at least 2/32. A steer tire with less than 2/32 tread depth is well below the legal minimum and must be replaced immediately.

  5. What is the purpose of a header board (headache rack) on a flatbed truck?

    • A. To provide a mounting point for clearance lights
    • B. To reduce wind resistance and improve fuel economy
    • C. To protect the cab from forward-shifting cargo
    • D. To support tarps covering the load

    Hint: The header board protects the cab from cargo that shifts forward during braking.

    Explanation: A header board (headache rack) is mounted behind the cab to protect the driver from cargo that shifts forward during hard braking or a collision. It acts as a barrier between the cargo and the cab.

  6. When transporting hazardous materials, placards must be placed on which sides of the vehicle?

    • A. Front and back only
    • B. Only on the side facing oncoming traffic
    • C. All four sides: front, rear, and both sides
    • D. Only on the rear of the vehicle

    Hint: Placards must be visible from all directions to warn emergency responders approaching from any angle.

    Explanation: Hazmat placards must be displayed on all four sides of the vehicle, front, rear, and both sides, so that they are visible from any direction. Each placard must be at least 10 3/4 inches square.

  7. Where must hazardous materials shipping papers be kept while driving?

    • A. In the glove compartment
    • B. In the trailer with the cargo
    • C. In a pouch on the driver's door
    • D. In a locked box mounted behind the cab

    Hint: Shipping papers for hazmat must be immediately accessible to the driver and to emergency responders.

    Explanation: Shipping papers for hazardous materials must be kept in a pouch on the driver's door or in clear view and within the driver's reach while the seat belt is fastened. This allows quick access in an emergency.

  8. If a hazardous material is leaking from your vehicle, what should you do first?

    • A. Continue driving to the nearest truck stop for help
    • B. Park the vehicle, secure the area, and keep people away
    • C. Try to identify and repair the leak
    • D. Call your dispatcher and wait for instructions

    Hint: A hazmat leak requires immediate containment actions focused on safety rather than cleanup.

    Explanation: If a hazmat leak is discovered, the driver should immediately park the vehicle away from populated areas, secure the scene, keep people away from the leak, and contact emergency services.

  9. When should a bus driver evacuate passengers?

    • A. When there is a fire or the bus cannot be safely moved
    • B. Whenever the bus breaks down
    • C. Only when instructed by emergency services
    • D. Only when the destination has been reached and the door cannot open

    Hint: Bus evacuation is a last resort that should only be initiated when remaining on the bus is more dangerous.

    Explanation: Passengers should be evacuated if there is a fire or danger of fire, or if the bus is in a position that makes staying inside dangerous and the bus cannot be safely moved.

  10. When driving a large commercial vehicle down a long, steep downgrade, you should:

    • A. Place the vehicle in neutral to reduce wear on the engine
    • B. Ride the brakes continuously to maintain a safe speed
    • C. Use a low gear and apply brakes intermittently with firm pressure
    • D. Accelerate slightly to maintain momentum

    Hint: Going down a long grade in a heavy vehicle requires a specific technique to prevent brake failure from overheating.

    Explanation: On long downgrades, use a low gear to let the engine help slow the vehicle and apply brakes with firm, intermittent pressure. Riding the brakes continuously causes them to overheat and fade, potentially resulting in total brake failure.

Tennessee material makes up 43 of the 113 questions in this pool. Mountain driving gets real attention: braking on long Smoky Mountain grades, what runaway truck ramps in East Tennessee are for, gear choice on steep Appalachian climbs, and rollover risk on curving mountain roads. City driving shows up too, with the lane changes and tight curves of the I-40 and I-65 interchange in Nashville and knowing truck routes and restricted roads around Memphis.

Several questions cover penalties. A DUI in your personal car still disqualifies your CDL, a second one is a lifetime disqualification, and driving after being placed out of service brings fines plus disqualification. Others cover seat belts at all times and the emergency equipment you must carry.

One trap: Tennessee licenses you at 18 but restricts you to in-state driving until 21. The study cards split the pool into 70 safe driving and cargo questions and 43 on rules and licensing, with 10 free in each.

Key Topics

  • Smoky Mountain grades and runaway truck ramps
  • Nashville and Memphis urban driving
  • DUI and out-of-service penalties
  • CDL classes, endorsements and placards
  • Securement, hours of service and coupling