Skip to content

Wyoming CDL study: Air Brakes questions

This deck holds all 46 air brake questions, with 10 free and explained. Do components first, the biggest group, then pressure and spring brakes. Wyoming's own air brake items are in general knowledge. Then take air brakes run 1.

1/10·0 done

Question Map

Correct Wrong Unseen

10 of 46 questions are free. The rest are in Pro.

At approximately what PSI does the governor normally cut in (let the compressor resume pumping)?

Free Air Brakes questions questions for the Wyoming CDL test

Plain-text version of this question set

  1. At approximately what PSI does the governor normally cut in (let the compressor resume pumping)?

    • A. Around 100 PSI
    • B. Around 60 PSI
    • C. Around 125 PSI
    • D. Around 150 PSI

    Hint: Cut-in is the lower edge of normal operating pressure, well above the warning level.

    Explanation: The cut-in pressure is typically around 100 PSI. When tank pressure drops to that level, the governor signals the compressor to start pumping again until cut-out (about 125 PSI) is reached.

  2. Why should air tanks be drained regularly?

    • A. To remove fuel that has leaked into the system
    • B. To reduce the air pressure to a safe storage level
    • C. To recharge the brake chambers with fresh air
    • D. To remove water and compressor oil from the tanks

    Hint: Water and oil collect at the bottom of the tanks.

    Explanation: Compressed air usually has some water and compressor oil in it. These collect in the air storage tanks and, if not drained, can foul the brake system. Tanks should be drained completely. Some tanks have automatic drain valves, but they should still be checked.

  3. What is the purpose of an alcohol evaporator in an air brake system?

    • A. To increase the air pressure in the storage tanks
    • B. To clean the brake linings
    • C. To slow down the compressor when temperatures rise
    • D. To reduce the risk of ice forming in the brake valves

    Hint: It is most important in winter conditions.

    Explanation: An alcohol evaporator puts alcohol into the air system to reduce the risk of ice in the air brake valves and other parts during cold weather. The alcohol level should be checked daily in cold weather.

  4. What does the application pressure gauge show, when a vehicle is equipped with one?

    • A. The air pressure being applied to the brakes
    • B. Total air pressure in the storage tanks
    • C. The pressure at which the spring brakes will engage
    • D. The pressure at which the governor will cut out

    Hint: It responds to how hard you push the pedal.

    Explanation: The application pressure gauge shows how much air pressure is being applied to the brakes when the brake pedal is pressed. (Not all vehicles have this gauge.) An increase in application pressure to maintain the same speed means the brakes are fading and you should be alert.

  5. How are spring brakes (parking/emergency brakes) on heavy trucks held in the released position?

    • A. By air pressure holding back powerful springs
    • B. By hydraulic pressure from the master cylinder
    • C. By an electric solenoid
    • D. By a mechanical hand lever

    Hint: Air keeps them off; loss of air lets them on.

    Explanation: Trucks and buses must have spring brakes for parking and emergency use. Powerful springs in the spring brake chambers apply the brakes when the air pressure leaves the chambers. Air pressure holds back the springs to keep the brakes released. If air pressure is lost, the springs apply the brakes.

  6. On a vehicle with a dual air brake system, what happens if one of the two air systems develops a leak large enough to lose all pressure?

    • A. The other system still operates the brakes on some wheels
    • B. Both systems fail and the vehicle has no brakes
    • C. The spring brakes will apply immediately, but the service brakes will still work normally
    • D. The compressor automatically shuts off

    Hint: Redundancy is the whole point of dual systems.

    Explanation: If one air system gets very low in pressure, either the front or the rear brakes will not be fully operational. However, the vehicle will still have brakes on the other axle(s) through the other system, allowing the driver to safely bring the vehicle to a stop. The low air pressure warning will come on.

  7. What does it mean if a CDL has a 'Z' restriction?

    • A. The driver cannot operate vehicles transporting hazardous materials
    • B. The driver cannot operate a vehicle with full air brakes
    • C. The driver is restricted to intrastate operation
    • D. The driver cannot operate vehicles with manual transmissions

    Hint: It is related to taking the test in a vehicle with air-over-hydraulic brakes.

    Explanation: The Z restriction is applied when the driver performs the skills test in a vehicle with air-over-hydraulic brakes rather than full air brakes. With a Z restriction, the driver cannot operate a commercial motor vehicle equipped with any type of full air brake system.

  8. Which vehicles built after specific dates are required to have ABS?

    • A. All air-braked vehicles built on or after March 1, 1997
    • B. Only buses and motorcoaches built on or after March 1, 1998
    • C. Truck tractors from March 1997, others from March 1998
    • D. Only vehicles over 80,000 pounds built after March 1, 1998

    Hint: The two key dates are about a year apart in the late 1990s.

    Explanation: The Department of Transportation requires ABS on truck tractors with air brakes built on or after March 1, 1997, and on other air-braked vehicles (trucks, buses, trailers, and converter dollies) built on or after March 1, 1998. Many vehicles built before these dates have been retrofitted with ABS.

  9. What is meant by 'brake lag' in an air brake system?

    • A. The delay between pressing the pedal and the brakes working
    • B. The time it takes for the spring brakes to fully release after starting the engine
    • C. The slowdown in compressor output during cold weather
    • D. The time the driver takes to perceive a hazard

    Hint: It is a small delay built into how compressed air moves through hoses.

    Explanation: Air brakes take more time to work than hydraulic brakes because air has to flow through the lines. The time required for the brakes to work after the brake pedal is pushed is known as brake lag. On a hard application, it takes about one-half second (about 0.4 second) for the air to flow and the brakes to fully apply.

  10. What is brake fade and when is it most likely to occur?

    • A. A reduction in air pressure when the compressor cannot keep up with use
    • B. The temporary slow release of the spring brakes after start-up
    • C. A loss of braking power caused by overheated brakes
    • D. An inability of the ABS system to detect wheel speed at very low speeds

    Hint: It is a heat problem, not an air problem.

    Explanation: Brakes have to absorb the energy of the moving vehicle, so they get hot. Mechanical drum brakes can get so hot that they fade: they stop working effectively because the heat makes the components expand and the brake linings lose friction. Brake fade is most likely on long downgrades where the brakes are used continuously.

There are 46 questions in this pool, none written only for Wyoming. Components lead with 14, ABS has 7, pressure readings and parking brakes 5 each, and dual systems and stopping distance 4 each.

Wyoming's air brake material is in general knowledge, and it is worth studying with this section: what the gauge should read before you drive, what the governor controls, when the low pressure warning comes on, when spring brakes apply on their own, the allowed leak rate on a single vehicle with the engine off, what the tractor protection valve does on a breakaway, and how to handle a total failure on a downgrade using an escape ramp, terrain and downshifting.

The numbers are the hard part. Learn the gauge, warning, leak and spring brake figures as one checklist and practice them in the order of the in-cab check.

Key Topics

  • The federal air brake restriction
  • Total brake failure on a mountain pass
  • Compressor, governor and gauges
  • Spring brakes and the tractor protection valve
  • ABS and dual systems