Nebraska CDL study: Air Brakes questions
Nebraska's 44 air brake questions sit in one deck with 10 free. Start on the component cards, which are almost a third of the pool, then pressure and parking brakes. When you can explain each check, take air brakes run 1.
Free Air Brakes questions questions for the Nebraska CDL test
Plain-text version of this question set
At approximately what PSI does the governor normally cut in (let the compressor resume pumping)?
- A. Around 100 PSI
- B. Around 60 PSI
- C. Around 125 PSI
- D. Around 150 PSI
Hint: Cut-in is the lower edge of normal operating pressure, well above the warning level.
Explanation: The cut-in pressure is typically around 100 PSI. When tank pressure drops to that level, the governor signals the compressor to start pumping again until cut-out (about 125 PSI) is reached.
Why should air tanks be drained regularly?
- A. To remove fuel that has leaked into the system
- B. To reduce the air pressure to a safe storage level
- C. To recharge the brake chambers with fresh air
- D. To remove water and compressor oil from the tanks
Hint: Water and oil collect at the bottom of the tanks.
Explanation: Compressed air usually has some water and compressor oil in it. These collect in the air storage tanks and, if not drained, can foul the brake system. Tanks should be drained completely. Some tanks have automatic drain valves, but they should still be checked.
What is the purpose of an alcohol evaporator in an air brake system?
- A. To increase the air pressure in the storage tanks
- B. To clean the brake linings
- C. To slow down the compressor when temperatures rise
- D. To reduce the risk of ice forming in the brake valves
Hint: It is most important in winter conditions.
Explanation: An alcohol evaporator puts alcohol into the air system to reduce the risk of ice in the air brake valves and other parts during cold weather. The alcohol level should be checked daily in cold weather.
What does the application pressure gauge show, when a vehicle is equipped with one?
- A. The air pressure being applied to the brakes
- B. Total air pressure in the storage tanks
- C. The pressure at which the spring brakes will engage
- D. The pressure at which the governor will cut out
Hint: It responds to how hard you push the pedal.
Explanation: The application pressure gauge shows how much air pressure is being applied to the brakes when the brake pedal is pressed. (Not all vehicles have this gauge.) An increase in application pressure to maintain the same speed means the brakes are fading and you should be alert.
How are spring brakes (parking/emergency brakes) on heavy trucks held in the released position?
- A. By air pressure holding back powerful springs
- B. By hydraulic pressure from the master cylinder
- C. By an electric solenoid
- D. By a mechanical hand lever
Hint: Air keeps them off; loss of air lets them on.
Explanation: Trucks and buses must have spring brakes for parking and emergency use. Powerful springs in the spring brake chambers apply the brakes when the air pressure leaves the chambers. Air pressure holds back the springs to keep the brakes released. If air pressure is lost, the springs apply the brakes.
Why should you never push the brake pedal repeatedly when the spring brakes are on?
- A. It can release the spring brakes unintentionally
- B. It can drain the alcohol evaporator
- C. It combines spring and air force, damaging them
- D. It can prevent the low pressure warning from working
Hint: Two strong forces pushing the same brake shoes in the same direction is the danger.
Explanation: If the spring brakes are on, you should never push the brake pedal down. The brakes could be damaged by the combined forces of the springs and the air pressure. Many brake systems are designed so that this does not happen, but not all systems are set up that way and you cannot tell from the cab whether yours is.
On a vehicle with a dual air brake system, what happens if one of the two air systems develops a leak large enough to lose all pressure?
- A. The other system still operates the brakes on some wheels
- B. Both systems fail and the vehicle has no brakes
- C. The spring brakes will apply immediately, but the service brakes will still work normally
- D. The compressor automatically shuts off
Hint: Redundancy is the whole point of dual systems.
Explanation: If one air system gets very low in pressure, either the front or the rear brakes will not be fully operational. However, the vehicle will still have brakes on the other axle(s) through the other system, allowing the driver to safely bring the vehicle to a stop. The low air pressure warning will come on.
What does it mean if a CDL has a 'Z' restriction?
- A. The driver cannot operate vehicles transporting hazardous materials
- B. The driver cannot operate a vehicle with full air brakes
- C. The driver is restricted to intrastate operation
- D. The driver cannot operate vehicles with manual transmissions
Hint: It is related to taking the test in a vehicle with air-over-hydraulic brakes.
Explanation: The Z restriction is applied when the driver performs the skills test in a vehicle with air-over-hydraulic brakes rather than full air brakes. With a Z restriction, the driver cannot operate a commercial motor vehicle equipped with any type of full air brake system.
Which vehicles built after specific dates are required to have ABS?
- A. All air-braked vehicles built on or after March 1, 1997
- B. Only buses and motorcoaches built on or after March 1, 1998
- C. Truck tractors from March 1997, others from March 1998
- D. Only vehicles over 80,000 pounds built after March 1, 1998
Hint: The two key dates are about a year apart in the late 1990s.
Explanation: The Department of Transportation requires ABS on truck tractors with air brakes built on or after March 1, 1997, and on other air-braked vehicles (trucks, buses, trailers, and converter dollies) built on or after March 1, 1998. Many vehicles built before these dates have been retrofitted with ABS.
What is meant by 'brake lag' in an air brake system?
- A. The delay between pressing the pedal and the brakes working
- B. The time it takes for the spring brakes to fully release after starting the engine
- C. The slowdown in compressor output during cold weather
- D. The time the driver takes to perceive a hazard
Hint: It is a small delay built into how compressed air moves through hoses.
Explanation: Air brakes take more time to work than hydraulic brakes because air has to flow through the lines. The time required for the brakes to work after the brake pedal is pushed is known as brake lag. On a hard application, it takes about one-half second (about 0.4 second) for the air to flow and the brakes to fully apply.
We have 44 air brake questions for Nebraska, all from the national manual. Components take the largest share with 14, followed by ABS with 7, pressure readings and parking brakes with 5 each, dual systems with 4 and stopping distance with 3. Spend most of your time on what each part does and how you check it.
Nebraska's General Knowledge pool also asks air brake questions: the governor cut-out range, the 60 psi warning point, spring brakes as a fail-safe and brake fade from long, hard braking. These overlap with what you will need for the brake check on skills day, so treat the two pools as one study block.
If you already hold a restricted CDL, changing a restriction costs $15 in Nebraska, the general change of class, endorsement or restriction fee. Ask the DMV what testing it needs from you, since a skills test in an air brake vehicle is likely part of it.
Key Topics
- Air brake restriction and the CLP
- Brake check failure ends the inspection
- Components and what each does
- Pressure readings and spring brakes
- ABS, parking brakes and stopping distance