# Maine CDL General Knowledge practice questions (free set) 40 of the 110 questions are written around Maine. Winter is a big part of them: jackknifing on winter roads, pulling off when a storm cuts visibility, when to watch for black ice, and checking lights on a dark winter morning. Others are about the roads themselves: snub braking on a mountain grade, merging and tolls on the Maine Turnpike, narrow rural roads with tight curves and wildlife, moose warning signs, older bridges with low weight limits, and reduced posted weights during the spring thaw. Cargo questions cover securing logs and timber, keeping live lobster at the right temperature, and oversize load permits. Interactive version with answers, hints and explanations: https://dmv-iq.com/maine-cdl-general-knowledge-test/study/safe-driving-and-cargo/ ## About the Maine CDL General Knowledge knowledge test - Issuing agency: BMV - Passing score: 80% - Source: the Maine Commercial Driver License Manual ## Topics covered - Maine winter, moose and rural road questions - Spring thaw limits and older bridges - Logs, timber and live seafood loads - OUI and disqualifications - Placards, securement and hours of service ## The 10 free questions This set has 73 questions in total; these 10 are free. The rest are in DMV IQ Pro. ### 1. When uncoupling a trailer, what should you do before disconnecting the air lines and electrical cables? - A. Release the fifth wheel latch - B. Pull the tractor forward - C. Remove the wheel chocks - D. Lower the landing gear Hint: The trailer needs structural support before you remove its connections to the tractor. Explanation: Before disconnecting air lines and electrical cables, you should lower the trailer landing gear to support the front of the trailer. This prevents the trailer from tipping forward. ### 2. When hauling a loaded trailer around a curve on a Maine road, what is the greatest risk if you are traveling too fast? - A. Engine overheating - B. Tire blowout - C. Rollover - D. Transmission failure Hint: A high center of gravity combined with centrifugal force creates the most dangerous scenario on curves. Explanation: The greatest risk when driving too fast around a curve with a loaded trailer is a rollover. Loaded trailers with a high center of gravity are particularly susceptible, and many Maine rural roads have sharp curves. ### 3. What should you do if your low air pressure warning comes on while driving? - A. Continue driving but avoid using the brakes until pressure rebuilds - B. Increase engine speed to help the compressor build pressure faster - C. Stop and safely park as soon as possible - D. Turn off the air dryer and switch to manual mode Hint: A low air pressure warning while driving requires immediate action to prevent complete brake failure. Explanation: If the low air pressure warning activates, you should stop and safely park as soon as possible. Continued driving risks losing braking ability entirely if pressure drops further, which would engage the spring brakes uncontrollably. ### 4. The longer the combination vehicle, the more the trailer will off-track. What should a driver do when making a right turn with a long trailer? - A. Speed up through the turn to reduce off-tracking - B. Turn the steering wheel quickly to complete the turn faster - C. Turn from the far right lane to minimize the turning arc - D. Swing wide to the left before turning right Hint: Longer vehicles have more severe off-tracking, requiring a specific turning technique. Explanation: With longer combination vehicles, drivers should swing wide or use a jug handle turn, moving slightly to the left before turning right to give the trailer wheels room to clear the curb and any objects on the inside of the turn. ### 5. Which of the following is an out-of-service condition that would prevent you from driving the vehicle? - A. A small crack in the windshield on the passenger side - B. Brake drums cracked through the wall - C. One burned-out clearance marker light - D. A missing mud flap on the rear axle Hint: Certain defects are so severe that the vehicle cannot legally be driven until they are repaired. Explanation: Cracked brake drums that have cracks extending through the drum wall are a critical out-of-service violation. The vehicle cannot be driven until the brake drums are replaced. ### 6. What is the maximum weight allowed on a single axle under federal bridge law? - A. 20,000 lbs - B. 15,000 lbs - C. 34,000 lbs - D. 25,000 lbs Hint: Federal bridge law sets specific weight limits for individual axles to protect road infrastructure. Explanation: Federal bridge law limits a single axle to 20,000 lbs and a tandem axle to 34,000 lbs. The total gross vehicle weight is limited to 80,000 lbs on interstate highways. ### 7. When transporting hazardous materials, placards must be placed on which sides of the vehicle? - A. Front and back only - B. Only on the side facing oncoming traffic - C. All four sides: front, rear, and both sides - D. Only on the rear of the vehicle Hint: Placards must be visible from all directions to warn emergency responders approaching from any angle. Explanation: Hazmat placards must be displayed on all four sides of the vehicle, front, rear, and both sides, so that they are visible from any direction. Each placard must be at least 10 3/4 inches square. ### 8. At a railroad crossing, a bus carrying passengers must: - A. Stop between 15 and 50 feet from the nearest rail - B. Slow down to 10 mph and proceed if the tracks are clear - C. Only stop if warning lights are flashing - D. Honk the horn and proceed across quickly Hint: Buses carrying passengers must follow stricter rules at railroad crossings than regular vehicles. Explanation: Buses carrying passengers must stop at railroad crossings no closer than 15 feet and no farther than 50 feet from the nearest rail. The driver must look and listen for trains before crossing. ### 9. When driving a large commercial vehicle down a long, steep downgrade, you should: - A. Place the vehicle in neutral to reduce wear on the engine - B. Ride the brakes continuously to maintain a safe speed - C. Use a low gear and apply brakes intermittently with firm pressure - D. Accelerate slightly to maintain momentum Hint: Going down a long grade in a heavy vehicle requires a specific technique to prevent brake failure from overheating. Explanation: On long downgrades, use a low gear to let the engine help slow the vehicle and apply brakes with firm, intermittent pressure. Riding the brakes continuously causes them to overheat and fade, potentially resulting in total brake failure. ### 10. When stopping at a railroad crossing in a CMV that is required to stop, the driver must stop between what distances from the nearest rail? - A. 5 to 25 feet - B. 10 to 30 feet - C. 15 to 50 feet - D. 25 to 75 feet Hint: The stopping distance at railroad crossings has specific minimum and maximum limits. Explanation: Commercial vehicles required to stop at railroad crossings must stop no closer than 15 feet and no farther than 50 feet from the nearest rail. The driver must then look and listen for approaching trains before proceeding. ## More - [Maine CDL General Knowledge test](https://dmv-iq.com/maine-cdl-general-knowledge-test/) - [Maine CDL General Knowledge practice run 1](https://dmv-iq.com/maine-cdl-general-knowledge-test/test-1/) - [Maine CDL practice test](https://dmv-iq.com/maine-cdl-practice-test/) DMV IQ builds its CDL questions from each state's official CDL manual and the federal FMCSA rules.