# Alabama CDL General Knowledge practice questions (free set) Of the 103 questions in this pool, 33 are written around Alabama. Several deal with oversize loads, asking which signs an oversize load must carry and at what width escort vehicles are needed on two-lane roads. Others cover the state's axle and gross weight limits, how far a load may extend past the vehicle, and how soon you must recheck cargo securement after you start a trip. Licensing questions ask which endorsements drivers aged 18 to 20 cannot hold and which knowledge tests a Class A permit requires. Interactive version with answers, hints and explanations: https://dmv-iq.com/alabama-cdl-general-knowledge-test/study/safe-driving-and-cargo/ ## About the Alabama CDL General Knowledge knowledge test - Issuing agency: ALEA - Passing score: 80% - Source: the Alabama Commercial Driver License Manual ## Topics covered - Alabama oversize load signs, escorts and load overhang - Alabama axle and gross weight limits - CDL classes, permits and age-limited endorsements - Hours of service and ELDs - Alcohol, refusals and disqualification - Railroad crossings and cargo securement ## The 10 free questions This set has 57 questions in total; these 10 are free. The rest are in DMV IQ Pro. ### 1. Which written knowledge tests must an Alabama applicant pass to obtain a Class A CLP? - A. The General Knowledge test only - B. General Knowledge and Air Brakes only - C. General Knowledge, Hazardous Materials, and Air Brakes - D. General Knowledge, Air Brakes, Combination Vehicles Hint: Class A applicants face the most extensive testing because they will operate the most complex vehicle combinations. Explanation: To obtain a Class A CLP in Alabama, applicants must pass the General Knowledge, Air Brakes, and Combination Vehicles written tests. ### 2. According to Alabama CDL regulations, what is the minimum combined working load limit for tie-downs securing general cargo? - A. One-quarter the weight of the cargo - B. Equal to the weight of the cargo - C. One-half the weight of the cargo - D. Twice the weight of the cargo Hint: Tie-down strength requirements are calculated as a fraction of the cargo weight being secured. Explanation: Tie-down systems must have a combined working load limit of at least one-half the weight of the cargo being secured to prevent shifting or falling during transport. ### 3. What should you do if your low air pressure warning comes on while driving? - A. Continue driving but avoid using the brakes until pressure rebuilds - B. Increase engine speed to help the compressor build pressure faster - C. Stop and safely park as soon as possible - D. Turn off the air dryer and switch to manual mode Hint: A low air pressure warning while driving requires immediate action to prevent complete brake failure. Explanation: If the low air pressure warning activates, you should stop and safely park as soon as possible. Continued driving risks losing braking ability entirely if pressure drops further, which would engage the spring brakes uncontrollably. ### 4. The longer the combination vehicle, the more the trailer will off-track. What should a driver do when making a right turn with a long trailer? - A. Speed up through the turn to reduce off-tracking - B. Turn the steering wheel quickly to complete the turn faster - C. Turn from the far right lane to minimize the turning arc - D. Swing wide to the left before turning right Hint: Longer vehicles have more severe off-tracking, requiring a specific turning technique. Explanation: With longer combination vehicles, drivers should swing wide or use a jug handle turn, moving slightly to the left before turning right to give the trailer wheels room to clear the curb and any objects on the inside of the turn. ### 5. When inspecting tires during a pre-trip inspection, which condition would require the tire to be replaced before driving? - A. A minor scuff mark on the sidewall - B. Tread depth of less than 2/32 of an inch on a steer tire - C. A tread depth of 5/32 of an inch on a drive tire - D. Slightly uneven tread wear across the tire Hint: Steer tires have stricter tread depth requirements than drive or trailer tires because they control the vehicle's direction. Explanation: Front (steer) tires must have at least 4/32 of an inch tread depth and all other tires at least 2/32. A steer tire with less than 2/32 tread depth is well below the legal minimum and must be replaced immediately. ### 6. When transporting hazardous materials, placards must be placed on which sides of the vehicle? - A. Front and back only - B. Only on the side facing oncoming traffic - C. All four sides: front, rear, and both sides - D. Only on the rear of the vehicle Hint: Placards must be visible from all directions to warn emergency responders approaching from any angle. Explanation: Hazmat placards must be displayed on all four sides of the vehicle, front, rear, and both sides, so that they are visible from any direction. Each placard must be at least 10 3/4 inches square. ### 7. Where must hazardous materials shipping papers be kept while driving? - A. In the glove compartment - B. In the trailer with the cargo - C. In a pouch on the driver's door - D. In a locked box mounted behind the cab Hint: Shipping papers for hazmat must be immediately accessible to the driver and to emergency responders. Explanation: Shipping papers for hazardous materials must be kept in a pouch on the driver's door or in clear view and within the driver's reach while the seat belt is fastened. This allows quick access in an emergency. ### 8. How many passengers must a vehicle be designed to carry (including the driver) to require a CDL with a P endorsement? - A. 16 or more - B. 10 or more - C. 12 or more - D. 20 or more Hint: The passenger threshold that triggers the CDL P endorsement requirement includes the driver in the count. Explanation: A CDL with a Passenger (P) endorsement is required to operate any vehicle designed to carry 16 or more passengers, including the driver. ### 9. When driving a large commercial vehicle down a long, steep downgrade, you should: - A. Place the vehicle in neutral to reduce wear on the engine - B. Ride the brakes continuously to maintain a safe speed - C. Use a low gear and apply brakes intermittently with firm pressure - D. Accelerate slightly to maintain momentum Hint: Going down a long grade in a heavy vehicle requires a specific technique to prevent brake failure from overheating. Explanation: On long downgrades, use a low gear to let the engine help slow the vehicle and apply brakes with firm, intermittent pressure. Riding the brakes continuously causes them to overheat and fade, potentially resulting in total brake failure. ### 10. When stopping at a railroad crossing in a CMV that is required to stop, the driver must stop between what distances from the nearest rail? - A. 5 to 25 feet - B. 10 to 30 feet - C. 15 to 50 feet - D. 25 to 75 feet Hint: The stopping distance at railroad crossings has specific minimum and maximum limits. Explanation: Commercial vehicles required to stop at railroad crossings must stop no closer than 15 feet and no farther than 50 feet from the nearest rail. The driver must then look and listen for approaching trains before proceeding. ## More - [Alabama CDL General Knowledge test](https://dmv-iq.com/alabama-cdl-general-knowledge-test/) - [Alabama CDL General Knowledge practice run 1](https://dmv-iq.com/alabama-cdl-general-knowledge-test/test-1/) - [Alabama CDL practice test](https://dmv-iq.com/alabama-cdl-practice-test/) DMV IQ builds its CDL questions from each state's official CDL manual and the federal FMCSA rules.